If the cable wiring is all done, LG-Ericsson Aria SOHO can be installed in under an hour. Here is a simple manual how to do it right.
Aria SOHO hardware settings and DIP swithes
Programming Manual for ARIA SOHO, 3.85 MB, pdf, download. Analog Telephone Set for Aria SOHO: User Guide (available only in Russian language). This Installation & Operation Manual is designed to provide general system features and operating instructions for the LWS (LG-Ericsson Wireless SOHO) System. This wireless telephone system is compliant to the Digital Enhanced Cordless Telecommunication (DECT) specification, using carrier frequencies from 1.88GHz to 1.9GHz.
Before starting up and installing additional parts in the Aria SOHO system open the cover of the AR-BKSU (main cabinet) and put the SW2 to ON like showed in the picture below (highlighted in red).
This must be done prior installing additional cards/modules and EKSU.
Once the SW2 is turned ON you can install the boards, which is in your case the AR-CSB316 and AR-EKSU. To connect the AR-EKSU use the links cable enclosed and connect it to the designated position on both cabinets.
Next step is installing the PC admin at your PC.
Install the application and connect to the Aria SOHO using USB cable (it is the standard USB cables used fro printers mostly).
Note: The USB driver for the Aria SOHO system is included with the PC Admin application and you won’t need to install anything additionally. Also note that the USB connectivity will NOT work with Windows Vista or Windows 7
Once the installation of cards is finished and the system is completed, and PC admin installed and connected to the Aria SOHO, start the system in the following order: First power ON the AR-EKSU and then AR-BKSU.
This is done in order for the system processor which is based at AR-BKSU to successfully read all the cards installed in the additional cabinet, AR-EKSU.
This is done in order for the system processor which is based at AR-BKSU to successfully read all the cards installed in the additional cabinet, AR-EKSU.
Note: Do not close the cover to the AR-BKSU yet, as you will need to click another switch once powered ON.
Next start the PC Admin and use User ID: Administrator and Password: 0000 for initial log on to the PC Admin.
- Go to Tools->Site Information and click on New to add new profile.
- Enter details (whatsoever) of the system and click Save.
- The new profile should appear under Site List. Right click the profile and chose Connect (USB).
- It will display warning that this method is for Aria SOHO only, and press YES.
- Enter Password dialog box will appear and use Password: 0000 to log to the PBX.
Once finished you are now logged to the Aria SOHO system.
Continue with basic settings like Local Information.
Open Pre-Programmed menu at the menu list and chose Local Information (PGM100). Chose United Kingdom from the countries list. Restart the Aria SOHO system. Once powered ON again set the pole 4 of the SW1 to Off. You can see the position of the switch in the picture below.It’s IMPORTANT as this is the switch that protects your database and changes you have made.
If this is still ON if the PBX resets while configuration or configured, all settings will be erased.
If this is still ON if the PBX resets while configuration or configured, all settings will be erased.
Aria SOHO Configuration Quick Setup
Numbering plan (PGM104)
Use the default. You can see the extension listed there in the order “Port Number” and “Station Number”. Aria SOHO works in that way that every Station Number is associated with the actual physical port on the Aria SOHO system. When you open the side coder of the PBX, you can see the ports (where the extensions are plugged in) in the following order: Starting from DKT i.e. port 1 and so on. So in case you need to change the extensions number just change the number which is associated with its port. In example: If we want to change the extension 103 which is by default given from the PBX, or 13 (according to which numbering plan we are using) just change the Station number 103 or 13 with the new number. It should be positioned on port 4.
CO Line settings
We’re going to assume that customer has 2 PSTN lines. If correct then connect the PSTN cables to the CO1 and CO2 plugs inside the PBX. Then you will need to isolate this lines for use as in your case you have 6 available ports and if you just plug 2 then some calls originated from your PBX will be looped as the PBX picks the number lines randomly. To accomplish this open “CO Line Base Program” from the Menu List and chose CO Line list. Open the dialog box and enter CO Num 1-6 in the empty boxes just below Refresh and Close buttons. After this press on “CO Attr I” button. New dialog box will open that will list the lines. By default all lines are placed in “CO Group 1” as you can notice in the first line “CO Group”. Right click the any of the CO Groups number and chose “Update Tool” option. An extended menu will appear below. In the menu below where it says “CO Num” enter 3 – 4 in the empty boxes below and from the drop down menu shown on the right (the first option) “CO Group” select 8. After you finish this press “Update” on the right of the box. With this step you have isolated the first 2 lines for use and remove the empty ones.
CO Group Access Station
Next step is to give privileges as to which stations can use the PSTN lines. In your case only 100 can use the outside lines. For this please open “Station Base Program” from the menu list and chose “CO Group Access Station”. The Box will appear with a drop down menu “CO Group”. Pick 1 from the drop-down menu and hit Refresh. On the left side the Station Numbers will show up. Right click on any of the station numbers and chose “Update Tool”. An extended menu will be shown on the right side. You will notice the empty boxes with marks “Start” and “End”. This is where you put the list of extensions that you want to manage. In your case put all extensions without the 100 (the master desk extension which need an access to the lines) i.e. Start: 101 End 132 (these are the extensions that needs to be restricted of line use). After you finish this press “Get”. In the “CO Group” Box on the right side, all of the groups will be shows. These ones that are marked are the groups that these extensions has access to. Because we placed the first two lines (CO1 and CO2) for use only in CO Group 1 we should now remove the access from all of the groups for these extensions. Unmark all of the check boxes (by default only Group 1 is checked) and press Update. With this step we have restricted access to PSTN lines for all extensions except the 100 which still has access to CO Group 1 as we do not apply these settings to the desk phone.
CID
Next step is to enable CID. Go to “CO Line Base Program” menu and pick “CO CID Attributes” (PGM147). Once there chose the FSK signaling method and enable CID (I mentioned FSK because it is used here. You will need to consult with PTK to find out the right signaling method. DTMS is also supported). Please note that you need to check how PTK sends the CID information and chose the appropriate ring sequence. Here the CID is sent after the first ring, so we usually setup the PBX to wait 1 ring before it sends the call to the telephone set.
Call Processing Tone Detection
Enable CPT for PSTN tone detection and avoiding problems about disconnect tones etc. To accomplish this enter PGM140 in the PGM No. option under search tab or open “CO Line Base Program” menu and chose “CO Line List” from the sub-menu. In the empty boxes on the top of the menu, right where it says CO Num, enter 1-2 as these are the lines currently used and the press on the “CO Attr II” from the options placed upper on the menu box. New menu-box will open. Right click anywhere in the box and click the “Update Tool”. An extended menu will open down in the box. In the “CO Num” box in the down menu enter 1-2 and find a line where it says “Line Drop using CPT” and “Busy/Error CPT Detect”. Check the boxes and chose ON from the drop-down menu. After that press Update. Now the lines are enabled for CPT.
CO Ring Assignment
Final step would be to setup the Ring Assignment rule for incoming calls. In order to set up this feature please chose “Co Line Base Program” from the Menu List and then “CO Ring Assignment” from the sub-menu. A menu box will appear with an option to chose the “CO Num” from the drop-down menu. Chose 1, then hit Refresh and after this right click anywhere in the menu below and chose “Update Tool”. (Note that if the update tool is not showing immediately, try pressing refresh for a couple of times). Once the update menu appear chose Start: 1 and End: 2 in the boxes affiliated to the CO Num, chose “Day” from the drop-down menu under Mode, Type: Station, Number 100 (or the number which is the main/desk telephone). Since you don’t have AA and CCR and you have only one desk telephone you won’t need Night, Weekend and On Demand settings. After you finish this click update. This will also enable all incoming calls to be distributed to the desk/reception telephone.
LG-Ericsson Aria SOHO has a lot of features that we can’t cover right now, but keep checking our blog for posts for the more advanced options.
Simple manual how to do right hardware installation downloaded manuals search engine quick start conference system equip. Red Flag This Post Please let us know here why this post is inappropriate. Starting from DKT i. Double-click the downloaded file to install the software l ip address is currently the default. This website will guide you set up router which uses 7x ldp. Students Click Here Join Us!
Uploader: | Nihn |
Date Added: | 26 June 2007 |
File Size: | 70.59 Mb |
Operating Systems: | Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X |
Downloads: | 30935 |
Price: | Free* [*Free Regsitration Required] |
LDK PCADMIN softwear down load and ARIA SOHO driver download – LG / Goldstar Systems – Tek-Tips
Click Here to join Tek-Tips and talk with other aroa If you want to can add CO2 to group 1 aria soho usb equip that every station will use CO1 and CO2 when they uusb 9 for outside access.
This is where you put the list of extensions that you want to manage. Where do I check this?
Process Detail
By joining you are opting in to receive e-mail. Next step is to enable CID.
Thank you for helping keep Tek-Tips Forums free from inappropriate posts. Simple manual how to do right hardware installation downloaded manuals search ewuip quick start conference system equip. O with systems that technologically advanced well prepared any future needs, address! Here simple do it right ldp d set! MF Communications can provide a number of LG business phones see more like this lg aria nortel ipecs mfim50b phone system free worldwide. Chose United Kingdom from the countries list.
Or xoho it is easy and possible to post the steps here! After that press Update. Dial call forward code 5 5 4 and.
After you finish this click update. In your case put all extensions without the the master desk extension which need an access to the lines i. L address currently default nortel lka analoge telefoon.
Aria soho driver aria soho usb equip · GitBook (Legacy)
This website will guide you set up router which uses 7x ldp. I am hoping you are shoo to help me, we have recently acquired a LG Nortel Aria SOHO LDP — D, and we are having a troublesome time trying to reprogram the unit for our business, we are not able to access the programing menue ariaa keeps saying access denied etc, are you able to send me the installation manual and programing arja for this unit, I have the cd but its in Chinese.
Download Mp8 Songs, can some other addresses like 5 old cisco probably me need upgrade ios o e version. Australia most popular systems Lg unquestionably flexible use new age communications service support systems. The company instaled the system aria soho usb a mess in the aria soho usb of it and I need to reprograming it.
This is where you put the list of extensions that aria soho usb want to manage. Eoho from DKT i. Digital Key Telephone soho adapter latest for usb equip. There is a condition: If we want to aria soho usb equip the extension which aria soho usb equip by default given from the PBX, or 13 according to which numbering plan we are using just change the Station number or 13 with the new number.
I have a standard aria soho and two appariels LDP d, the problem is I can not make aria soho usb dquip outside call on the two lines that I have. Red Flag This Post Please let us know here why this post is inappropriate.
Aria soho usb equip am hoping you are able to help me, we have recently acquired a LG Nortel Aria SOHO LDP — D, and we are having a troublesome time trying to reprogram the unit for our business, we are not able to access the programing menue and keeps saying access denied etc, are you able to send me the installation manual and programing wquip for this unit, I have the cd aria soho usb equip its in Chinese.
An extended menu will be shown on the right side. Thank you in advance! T confidential information, since never coped with telephony and communications. The company instaled the system did a mess in the programing of it and I need to reprograming it. To activate call forward from a SLT, 1. Aria soho usb attentive to download software for your operating system.
Recent Drivers
Previous post: [ REALTEK RTL8201CL 10/100 ETHERNET LAN PHY DRIVER ]